RicochetStarlink

Reach out to Starlink Support.

I assume that Starlink Security Key means your WiFi Network password. You account password is NOT your WiFi password. If you set it up that what, change it. Immediately. If you do not know your WiFi Network password, you can change it using the mobile app.

You will need to install a Dual-WAN router than can handle two Internet connections if you want to use both connections simultaneously. This requires somewhat advanced knowledge of networking. I've actually done this and found that it works well, but I was using a $2,500 commercial router and had someone skilled who was willing to help me with the setup.

Do you have the Starlink Mobile app installed? It will tell you if there are obstructions. It will also tell you how often the antenna is unable to connect to a satellite. However, the problem may be with the WiFi signal. Have you split the 2.4GHz and 5GHz networks? Have you reset your router? It's possible that none of these suggestion will help. I'm hitting some of the common issues because there's no enough info to be more specific. Another suggestion: reach out to Starlink Support. HTH...

https://www.starlink.com/support/article/f3cad923-ed28-f957-365c-787f8fe2e4a2

That's definitely problematic. You concerns about water damage are valid. I would contact Starlink Support and see what they can do to help. It's unlikely you'll be able to repair it on your own. https://www.starlinkmap.org/

That depends on the length of your home. Starlink mesh router work best when less than 100' apart.

@jstruthers68, did you ever get a response from Starlink?

@Peter12, You don't have any tunable options to optimize the satellite network of your Starlink system. There are several options to tune/optimize your WiFi network. One of the key things to do is to split the 2.4GHZ and 5GHZ wireless networks using the apps. Many have had success using third-party mesh routers with their Starlink kit. It does require bypassing the Starlink WiFi Router and requires an Ethernet Adapter available in the Starlink store. Your Starlink system should be updating the firmware at least once/month, if not more frequently. This is automatic IF YOU LEAVE THE SYSTEM POWERED ON 24/7. The only mitigation for peak hour performance declines is to purchase a Priority Data plan. However, this does not guarantee improvements in every situation. It just means you are less likely experience performance declines. HTH.

Starlink's Satellite Internet is a completely different thing that other Satellite Internet Service. Other Satellite Internet provides have one large satellite that is in "geo-synchronous" orbit. This means it always appears to be at the same place in the sky above the earth. That's why you have to point your Dish antenna to the Southwest. It is also why, in some regions, the satellite can be "too low" (i.e., near or even below the horizon). Starlink, however has several thousand satellites. As of this moment, 5,601 according to https://www.starlinkmap.org/. This Starlink Map is provided by SpaceX/Starlink themselves. As you can see all 5601 of these satellites are constantly moving. So, wherever you set up starlink, you need a fairly broad view of the overhead sky so that it can detect satellites entering your visibility before the one you are currently connected to goes out of visibiilty. The hand-off from one satellite to the next is automatic and invisible to you. ALl that being said, 12% - 13% obstruction *MIGHT* be enough to get good service... generally, teh lower the obstruction %-age, the better. I'm assuming you probably do not want to cut down any redwoods, so moving your Starlink antenna higher off the ground. Of couse, after a while, this can get challenging. You might want to seek out a Starlink installation service for assistance.

That's a question for Starlink themselves. I've no idea.

No. The price of the HD equipment used in the Business subscription is much higher than the home kit. In the US it was running about $2,500 last time I checked.

Thanks for sharing the answer to this question @QTip.

Starlink uses Carrier-Grade NAT (CGNAT) which does not provide for routing ports to internal IP addresses. I don't think you can accomplish what you want here.

This is a question for Starlink Support.